2003 Honda Civic EX 1.7L L4 Gas Cold Air Intakes

57-3513 K&N Performance Air Intake System

K&N

57-3513 K&N Performance Air Intake System

$399.99 USD reg price
$349.99 sale price
$50.00 off for a limited time
Overview
A high-density polyethylene (HDPE) rotationally-molded tube helps increase the volume of airflow to your engine, and provides a guaranteed increase in horsepower and torque. These systems are paired with a washable, reusable High-Flow Air Filter™ featuring oiled cotton filter media. The oversized, conical design allows you to go up to 100,000 miles between filter services under normal highway driving conditions. A custom heat shield helps protect intake air from the high temperature of your engine bay, and the entire system can typically be installed in less than 90 minutes. Some intakes are not legal for sale or use on any pollution controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.
More Information
Specifications
Vehicle Applications
Cross References

69-1008TS K&N Performance Air Intake System

K&N
DIY LEVEL
EASY
MODERATE
ADVANCED

69-1008TS K&N Performance Air Intake System

$429.99 USD reg price
$379.99 sale price
$50.00 off for a limited time
Overview
The K&N 69-1008TS Typhoon air intake system is a free-flowing, mandrel-bent aluminum tube air induction system. The restrictive factory air filter and air intake housing are replaced by the K&N Typhoon air intake which is designed to dramatically reduce air flow restriction as it smoothes and straightens air flow. This allows your engine to inhale a larger amount of air than the factory air intake. More air means more usable power and acceleration throughout the engine's RPM range. The 69-1008TS air intake comes with a black rubber topped K&N high-flow air filter that installs into the previous air box space. Air is directed through the intake tube into the engine's throttle body for a guaranteed power gain. The intake tube has an attractive silver powder-coat finish that's made to last and it accommodates the factory air temperature sensor and crank case vent hose. The oversized cone shaped air filter can be used for up to 100,000 miles before servicing is needed depending on driving conditions. This air intake is relatively easy to install usually in 90 minutes or less using existing factory mounting points. The tools needed are a screwdriver, pliers, ratchet set and an Allen wrench. Some Typhoon air intakes are not legal for sale or use in California and other states adopting California emission standards while others are CARB exempt and 50 state legal. Check the K&N catalog or website for vehicle applications and specific CARB status for each vehicle and air intake.
More Information
Specifications
Vehicle Applications
Cross References
DIY LEVEL
EASY
MODERATE
ADVANCED

69-1007TS K&N Performance Air Intake System

K&N
DIY LEVEL
EASY
MODERATE
ADVANCED

69-1007TS K&N Performance Air Intake System

$479.99 USD reg price
$429.99 sale price
$50.00 off for a limited time
Overview
The K&N 69-1007TS Typhoon cold-air intake system is a free-flowing, mandrel-bent aluminum tube air induction system designed to fit some Honda Civic VI, SI, LX, HX, EX and DX models. The restrictive factory air filter and air intake housing are replaced by the K&N Typhoon cold-air intake which is designed to pull in outside air and dramatically reduce air flow restriction by smoothing and straightening air flow. This allows your engine to inhale a larger amount of air than the factory air intake. More air means more usable power and acceleration throughout the engine's RPM range. The 69-1007TS cold-air intake consists of a black rubber topped K&N high-flow air filter that mounts near the passenger side wheel well directing outside air through free-flowing aluminum tubing into a short ram induction tube that delivers high volumes of clean air into the engine's throttle body for a guaranteed power gain. The intake tubes have an attractive silver powder-coat finish that's made to last. The cold-air intake system accommodates the factory air temperature sensor and a replacement silicone crankcase vent hose. The oversized cone shaped air filter comes with a water repellent DryCharger filter wrap to protect the filter from moisture. The air filter can be used for up to 100,000 miles before servicing is needed depending on driving conditions. This cold air intake is relatively easy to install usually in 90 minutes or less using existing factory mounting points. The tools needed are a screwdriver, pliers, ratchet set and an Allen wrench. Some Typhoon air intakes are not legal for sale or use in California and other states adopting California emission standards while others are CARB exempt and 50 state legal. Check the K&N catalog or website for vehicle applications and specific CARB status for each vehicle and air intake.
More Information
Specifications
Vehicle Applications
Cross References
DIY LEVEL
EASY
MODERATE
ADVANCED

69-1008TB K&N Performance Air Intake System

K&N
DIY LEVEL
EASY
MODERATE
ADVANCED

69-1008TB K&N Performance Air Intake System

$429.99 USD reg price
$379.99 sale price
$50.00 off for a limited time
Overview
The K&N 69-1008TB Typhoon air intake system is a free-flowing, mandrel-bent aluminum tube air induction system. The restrictive factory air filter and air intake housing are replaced by the K&N Typhoon air intake which is designed to dramatically reduce air flow restriction as it smoothes and straightens air flow. This allows your engine to inhale a larger amount of air than the factory air intake. More air means more usable power and acceleration throughout the engine's RPM range. The 69-1008TB air intake comes with a black rubber topped K&N high-flow air filter that installs into the previous air box space. Air is directed through the intake tube into the engine's throttle body for a guaranteed power gain. The intake tube has an attractive blue powder-coat finish that's made to last and it accommodates the factory air temperature sensor and crank case vent hose. The oversized cone shaped air filter can be used for up to 100,000 miles before servicing is needed depending on driving conditions. This air intake is relatively easy to install usually in 90 minutes or less using existing factory mounting points. The tools needed are a screwdriver, pliers, ratchet set and an Allen wrench. Some Typhoon air intakes are not legal for sale or use in California and other states adopting California emission standards while others are CARB exempt and 50 state legal. Check the K&N catalog or website for vehicle applications and specific CARB status for each vehicle and air intake.
More Information
Specifications
Vehicle Applications
Cross References
DIY LEVEL
EASY
MODERATE
ADVANCED

We use cookies to personalize content and ads, to provide social media features and to analyze our traffic. We also share information about your use of our site with our social media, advertising and analytics partners. Learn more.

ALLOW COOKIES