Automotive Air Filters
Motorcycle / ATV Air Filters
Universal & Clamp-on Air Filters
Cabin Air Filters
Industrial / Small Engine Air Filters
Heavy Duty Diesel Air Filters
Racing and Custom Air Filters
Marine Flame Arrestors
Crankcase Vent Filters
Air Filter Facts
Air Filters by Vehicle Manufacturer
Cabin Air Filters by Vehicle Manufacturer
Automotive Air Intakes
Motorcycle / ATV Air Intakes
Diesel Truck Air Intakes
RV Air Intakes
Air Intake Installation Videos
Air Intake Installation Instructions
Air Intakes by Vehicle Manufacturer
Automotive Oil Filters
Motorcycle / ATV Oil Filters
Marine Oil Filters
Heavy Duty Diesel Oil Filters
Oil Filters by Vehicle Manufacturer
Automotive Performance Parts
Motorcycle / ATV Performance Parts
Diesel Fuel Filters
In-Line Fuel Filters
In-Line Fuel Pumps
Marine Performance Parts
Search by Vehicle
Search by Part
Search by Dimension
Search by VIN
Cross Reference Search
News and Events
SEARCH BY VEHICLE
Motorcycle & ATV
ALL or Unknown Year
K&N Intake System Frees Up An Extra 18 Horsepower For Brutish American-Made Dodge Viper
The 2008 Dodge Viper defines brute power. Equipped with an 8.4-liter, 10-cylinder engine, the 2008 Dodge Viper is capable of producing over 600 horsepower. The Viper is often considered primitive when compared to ultra-luxurious supercars from Europe. However, what the Viper lacks in plush trim and options, it makes up for with its track credentials.
Air Intake for Dodge Viper 8.4-liter V10
Air Intake installed on 2008 Dodge Viper 8.4-liter V10
2008 Dodge Viper SRT10
69-2527TTR gained 18.69 horsepower for the 2008 Viper
The 2008 Viper is reported to accelerate from 0-60 mph in 3.7 seconds, cover the quarter mile in 11.8 seconds, and reach top speeds of around 200 mph. Combine that level of sheer power with the ability to precisely maneuver through turns, stop from 60-0 mph in around 100 feet, and the 2008 Viper will leave a venomous taste in mouths of European supercar owners.
K&N engineers are always hunting for more power. After looking under the hood of the 2008, 2009 and 2010 Dodge Viper, K&N engineers knew the Viper was capable of more. Much consideration was put into the design of part number
The stock Viper intake tract uses a dual throttle body set up fed by a common plenum with a single air filter. K&N intake
replaces the stock pieces with twin powder coated mandrel-bent aluminum intake tubes and dual K&N high-flow air filters for improved air delivery.
This performance air intake system incorporates a unique heat shield, and the dual air filters line up with the factory fresh air intake on the hood. The result of this hard work and enthusiasm for performance is a nearly 19 horsepower gain at the wheels.
K&N’s Research and Development Department tested a 2008 Dodge Viper 8.4-liter V10 on our in-house dynamometer.
showed horsepower increases throughout the RPM range with a shocking peak horsepower gain of 18.69 horsepower @ 5,300 RPM!
provides improved performance with attractive red powder coated aluminum intake tubes to match the 2008 Viper’s valve covers.
K&N air intakes completely replace the restrictive factory air intake assembly with an aerodynamically engineered tube and an oversized air filter. With a
K&N Performance Air Intake System
, consumers can
count on extra horsepower
whether cruising along with fellow Viper owners, or competing at Laguna Seca.
This air intake system uses two conical shaped, chrome topped, high-flow air filters (
) and a powder coated aluminum heat shield in place of the vehicle's stock air box. The result is an air filter that captures harmful particles, flows more air, and provides long service life. This K&N air filter performs for up to 100,000 miles before service is required, depending on driving conditions. Improving the air path between the filter and the engine are the powder coated aluminum intake tubes. Our powder coated aluminum intake tubes offer power and a stylish appearance.
takes about 90 minutes or less to install, using stock mounting points, requires no drilling, and is covered by the
K&N Million Mile Limited Warranty®
For increased protection and style, K&N intake
filter wraps (
) intended be used during inclement weather. Drychargers® are made from a durable polyester material containing uniform micron openings which will stop small dirt particles and repel water; yet add little restriction to the airflow of the filter. Available in a variety of colors, K&N Drychargers® can be color coordinated with a car’s finish.
Find K&N products for your vehicle using the
K&N application search
then use the
K&N dealer search
to find a K&N dealer in your part of the world.
See What K&N Makes for Your Car!
Get the K&N Newsletter!
Did you like this story? Select 1 to 5 stars to rate it.
K&N Engineering, Inc., with headquarters in Riverside, California, has been the world's leader in performance filter technology since 1969, serving the needs of the automotive, motorcycle, marine, industrial and military markets. K&N is heavily involved in nearly every form of motorsports from off-road and powersports to drag racing, stock cars and road racing. For more information about K&N Filters, please contact K&N Engineering, Inc., P.O. Box 1329, Riverside, CA 92502-1329, (800) 213-4182 for a dealer near you, (800) 858-3333 for technical service/questions, (951) 826-4001 Fax, e-mail firstname.lastname@example.org, or visit www.knfilters.com.
K&N News Home