| Due to the differences in engine compartment designs, and accessories supplied by those manufactures, clearances may vary from boat to boat. The applications listed in this brochure are to be used as a reference guide only. Make sure to double check all the measurements before ordering by using the checklist below. If you wish to increase or decrease the size of
the filter, see Universal 3-Piece assemblies below. (#59-1195
shown in picture) |
|
|
Indmar |
Engine & Fuel System
Size Total Ht Element Ht Part #
Footnotes
5.7L Malibu Vortec 4 bbl 5.7L V8 3.75" 2"
59-3264 1
5.7l Vortec Carb 4 bbl 5.7L V8 3.75" 2"
59-3264 1
5.7L Vortec TBI 5.7L V8
3.75" 2"
59-3264 1,3
7.4L 4 bbl 7.4L V8
3.75" 2"
59-3264 1
7.4L MPI 7.4L V8
N/A N/A
59-5020
8.1L 4 bbl 8.1L V8
4.50" 2.75"
59-3364 1,2
8.1L PFI 8.1L V8
N/A N/A
59-5020 |
|
Mercury |
Engine & Fuel System
Size Total Ht
Element Ht Part # Footnotes
3.0L 2 bbl*
3.0L L4 3.75" 2"
59-3264 1
4.3L 2 bbl*
4.3L V6 3.75" 2"
59-3264 1
4.3LH 4 bbl
4.3L V6 3.75" 2"
59-3264 1
4.3L EFI TBI
4.3L V6 3.75" 2"
59-3264 1,3
5.0L 2 bbl*
5.0L V8 4.50" 2.75"
59-3364 1,2
5.0L EFI TBI
5.0L V8 4.50" 2.75"
59-3364 1,2,4
5.7L 2 bbl*
5.7L V8 4.50" 2.75"
59-3364 1,2
5.7L SKI 2 bbl*
5.7L V8 4.50" 2.75"
59-3364 1,2
5.7L EFI TBI
5.7L V8 4.50" 2.75"
59-3364 1,2,4
Early 4.3., 5.0, 5.7 MPI All
7
Late 4.3., 5.0, 5.7 MPI All
8
98-00 Mercruiser
7.4L V8 6.625" 6"
59-5004
Early Mercruiser MPI 3V Pulley 454 MAG 4.375"
4"
59-4541
5
Early Mercruiser MPI 3V Pulley 502 MAG 4.375"
4"
59-4541
5
Late MPI Serpentine Belt 454 MAG
4.375" 4"
59-4542 6
Late MPI Serpentine Belt 502 MAG
4.375" 4"
59-4542 6
496 MPI
8.1L V8 4.375" 4"
59-5005
496 HO & Mag MPI
8.1L V8 4.375" 4"
59-5005
HP 500 4 bbl
8.2L V8 6.75" 5"
59-3370 1,2
HP 500 MPI
8.2L V8 4.375" 4"
59-5020
|
|
Volvo
Penta |
Engine & Fuel System Size Total Ht
Element Ht Part # Footnotes
SX SERIES
3.0 GS 2 bbl* 3.0L L4 3.75" 2"
59-3264 1
4.3GL 2 bbl* 4.3L V6 3.75"
2"
59-3264 1
4.3L Gi EFI-TBI
4.3L V6 3.75" 2"
59-3264 1,3
5.0GL 2 bbl*
5.0L V8 4.50" 2.75"
59-3364 1,2
5.0L Gi EFI-TBI 5.0L V8
4.50" 2.75"
59-3364 1,2,4
5.7 GS 2 bbl*
5.7L V8 4.50" 2.75"
59-3364 1,2
5.7L Gsi EFI-TBI 5.7L V8
4.50" 2.75"
59-3364 1,2,4
7.4 Gi MPI
7.4L V8 4.50" 2.75"
59-3364 1,2,4
DUOPROP SERIES
4.3GL 2 bbl*
4.3L V6 3.75" 2"
59-3264 1
4.3L Gi EFI-TBI 4.3L V6
3.75" 2"
59-3264 1,4
5.0GL 2 bbl*
5.0L V8 4.50" 2.75"
59-3364 1,2
5.0L Gi EFI-TBI 5.0L V8
4.50" 2.75"
59-3364 1,2,4
5.7 GS 2 bbl
5.7L V8 4.50" 2.75"
59-3364 1,2
5.7L Gsi EFI-TBI 5.7L V8
4.50" 2.75"
59-3364 1,2,4
7.4 Gi EFI-MPI
7.4L V8 4.50" 2.75"
59-3364 1,2,4
7.4 Gsi EFI-MPI 7.4L V8
4.50" 2.75"
59-3364 1,2,4
8.1L MPI EFI-MPI 8.1L V8
4.50" 2.75"
59-3364 1,2,4
HIGH-END SERIES
DPX 385 EFI-MPI 7.4L/454
4.50" 2.75"
59-3364 1,2,4
DPX 415 EFI-MPI 8.2L/502
4.50" 2.75"
59-3364 1,2,4
DPX 500 EFI-MPI 8.2L/502
4.50" 2.75"
59-3364 1,2,4
DPX 600 EFI-MPI 8.8L/540
4.50" 2.75"
59-3364 1,2,4
INBOARD SERIES
7.4Gi EFI-MPI
7.4L/454 4.50" 2.75"
59-3364 1,2,4
PLATINUM SERIES
7.4Gi EFI-MPI
7.4L/454 4.50" 2.75"
59-3364 1,2,4 |
|
IMPORTANT:
DID YOU CHECK THE FOLLOWING? |
1. Diameter clearance around the existing flame arrestor. Can the flame arrestor diameter be increased?
2. Height restriction, due to hatch clearance or any other obstruction. Can the flame arrestor’s height be increased?
3. Do any vent lines connected to existing flame arrestor. If there are vent lines attached, measure inside diameter of vent line and order appropriate vent
hose kit below.
4. For multiple carburetor application, check center to center measurements ensuring enough space for two flame arrestors.
5. Check diameter of carburetor.
|
| Footnotes for above
applications: 1) May increase size as needed 2) May decrease size as needed
3) Use Z-stud Part #08008 4) Use Z-stud Part #08009 5) Kit
includes adapter Part # 85-8837 and flame arrestor Part #
59-5005
6) Kit includes adapter Part #
85-8837 and flame arrestor Part #
59-5006
7) Single Stud, 3-7/8” throttle body 8) 3 Studs, 3-5/8” throttle body |
* Fits Holley 2 bbl. For Rochester 2 bbl. (3 1/16” Neck Flange) use Part #59-3262 or #59-3362.
|
Universal
3-Piece Filter Assembly |
 |
 |
 |
| #59-5004 on 98-00 Mercruiser 7.4L |
#59-3364 on Carb Application |
#59-5005 on Mercruiser 496 HO |
 |
 |
 |
| #59-5020 on Mercruiser HP 500 |
Vent Hose Adapter on 3 Piece Assembly |
#59-4541 on Mercruiser 454/502 Magnum |
Outside Flange
Element Total Velocity
Diameter Diameter Height Height Stack
Part #
14"
5-1/8" 2.25" 3.87" No
59-3214
14" 5-1/8" 3.0"
4.62" No
59-3314
14" 5-1/8" 4.0"
5.62" No
59-3414
9" 5-1/8" 2.75"
4.5" No
59-3364
9" 5-1/8” 2.0"
3.75" No
59-3264
9" 5-1/8" 5.0"
6.75" No
59-3370
9" 5-1/8" 2.75"
8.5" Yes
59-1195
9" 5-1/8" 5.0"
10.75" Yes
59-1196
9" 4-7/32" 2.75"
4.5" No
59-3368
9" 3-1/16" 2.0"
3.75" No
59-3262
9" 3-1/16" 2.75"
4.5" No
59-3362
9" 2-5/8" 2.75"
4.5" No
59-3360
9" 7-5/16” 5.0"
10.75" Yes
59-1198
9" 7-5/16" 2.75"
4.5" No
59-0284
9" 7-5/16" 2.75"
8.5" Yes
59-3366
9" 7-5/16” 5.0"
6.75" No
59-1197
|
|
Marine
Vent Hose Adapters (Trimming
for correct height may be required) |
|
Clamp-Ons |
|
Type Flange
Length Width
Height Notes
Part #
Oval 2.93"x4.75" 6.5"
4.75" 5.62" GM TPI
59-5000
Oval 2.93"x4.75" 8.62"
4.5" 3.18" GM LT-1 No Vent
59-5020
Oval 2.93"x4.75" 8.62"
4.5" 3.18" GM LT
5/8" Vents(2)
59-5021
Oval 2.93"x4.75" 8.62"
4.5" 3.18" GM LT-1
5/8" Vent
59-5019
Oval 2.93"x4.75" 8.62"
5.25" 5.5" GM 454 TPI
59-5050
Oval 3.44"x5.44" 8.5"
5.06" 5"
59-5007
Rnd 3.75" 9.5"x4.625"B 8.5"x3.75"T
4" 454/502 MAG
59-5005
Rnd 3.75" 9.5"x4.625"B 8.5"x3.75"T
4" 454/502 MAG 1/2" Vent
59-5006
Rnd 3.5"
5" 4.5"x3.25"
5"
59-5003
Rnd 3.625" 5.75"
3" 6"
59-5004
Rnd 3.625" 5.75"
3" 6"
96-97 GM 2) 3/4" Vnts
59-5001
Rnd 3.75" 9.31"
4.5" 3"
96-97 GM (2) 5/8" Vnts 59-5022
Rnd 3.75" 9.31"
4.5" 3"
96-97 GM (2) 3/4" Vnts 59-5023
Rnd 3.75" 9.31"
4.5" 3"
96-97 GM
59-5030
Rnd 3.75" 9.31
4.5" 3"
96-97 GM 5/8" Vent
59-5010
Rnd 3.75" 5.25"
3" 6"
59-2030
Rnd 4"
5.38" 4.5x3.25"
5"
59-5002
|
|
 |
Copyright © 2012 K&N Engineering, Inc. All Rights Reserved.
|
